ABOUT                            SERVICES                            CONTACTS
Global
CATALOGUE
ASSORTMENT   
SERVICES
    Where To Buy
    New Release & Regional Booklet
    How To . . . . . . .
    Warranty Registration
 
    How To . . . . . . .

ZengaZ Lighters are available in a variety of styles for the most demanding aficionado.
ZengaZ product strictly adheres to ongoing safety testing requirements, precise and high quality products proudly to meet the performance criteria of ISO standard, EN and ASTM standard.

INSTRUCTIONS FOR USE

IGNITING THE LIGHTER
• A simple push on the ignition switch ignites a powerful flame over 2,000 degrees. This flame can be nearly invisible in bright light, so proper care is recommended.

TAKE CARE NOT TO TOUCH THE LIGHTER TOP AFTER IGNITION
• To avoid heat buildup, do not use in any situation that would require a continuous flame for more than 10 seconds.  the lighter may become too hot and cause harm to the lighter and/or the user.

EXTINGUISHING THE FLAME
• Releasing pressure from the ignition button of the lighter immediately extinguishes the flame by stopping fuel flow. If flame continues, the flame level is set too high and should be adjusted by turning the adjustment lever of the lighter towards the (-) position.

ADJUSTING FLAME LEVEL
• Turn the fuel adjustment lever of the lighter towards the (+) mark to increase the flame and turn the lever towards the (-) to decrease the flame to achieve a desired height. FILLING AND RE-FILLING LIGHTER 1. Release all tank pressure by pressing on the inlet valve with a small screwdriver. Hold the lighter vertical while bleeding valve. Repeat this several times until all fuel/gas pressure is released.
2. Set flame adjustment to lowest setting (-).
3. Turn lighter in upside down position and insert butane tank tip directly on the fuel valve. Do not shake the can of butane! This increases the amount of propellant in the mixture that goes into the lighter, and should not be done. Press down firmly for only about 5 seconds.
4. Before igniting lighter, wait 3-4 minutes. This allows excess butane to evaporate and gas inside lighter to reach room temperature.
5. Set flame level to desired height by turning flame adjuster lever.

Download ZengaZ Lighter Instruction Manual >>

PRECAUTIONS OF FILLING AND REFILLING

WARNING: PLEASE READ BEFORE OPERATING YOUR LIGHTER!
Keep out of Reach of Children & Away from all open flame sources
• Lighter contains flammable gas under pressure. Handle carefully.
• Ensure that flame is extinguished before attempting to fill.
• Never attempt to ignite lighter while refilling.
• Read butane canister warning labels.
• Only refill lighter in a well-ventilated area.
• Hold lighter away from face and clothing while filling lighter.
• Never fill lighter around any heat source, sparks or flame.
• Premium butane is highly recommended, as lower quality butane has been known to clog lighters.

HIGH ALTITUDE INSTRUCTIONS

• While triple refined premium fuel is recommended for all altitudes, the use of premium fuel in high altitudes is essential. Keep the fuel tank as full as possible at all times.
• After refilling lighter and before igniting, allow for fuel temperature to equal room temperature by holding the lighter in your hand for 1-2 minutes.
• To prevent freezing, keep lighter in an inside pocket.
• To improve ignition and flame height, turn the adjustment lever to the (-) setting to allow more oxygen in the combustion chamber. This compensates for the lack of oxygen at higher altitudes. At lower altitudes, turn adjustment wheel towards the (+) setting to increase fuel flow.
• If necessary, ignite the lighter slowly and carefully to follow the gas, spark, flame sequence. After hearing gas flowing, depress the trigger to ignite a flame. Do not repeatedly and quickly attempt to ignite a flame. A slow, deliberate motion increases your chances of ignition.
• When not in use, keep adjustment setting at medium and adjust (+) and (-) as needed.

SUGGESTIONS FOR CLEANING AND MAINTENANCE

CARING FOR YOUR LIGHTER
Lighters not in use / Lighters in storage
• Before storing lighters, empty all fuel. If your lighter has not been used for a long period of time and it appears to be no longer working, empty all fuel from the lighter by following step 1 in the filling/ re-filling instructions, then refuel and adjust the flame level. This should correct any problems.

Cleaning your Lighter
• Occasionally dust and or lint can clog the ignition valve, causing the lighter to malfunction. To clear obstructions such as these, blow a burst of air into the ignition valve.

Everyday storage of your lighter
• To prevent scratches and dings to your lighter from normal storage in a pocket or car console, we recommend you keep your lighter in a pouch.

If you have additional questions, please contact us.

 
 
MAIN               CATALOGUE               ABOUT               SERVICES               CONTACTS               LEGAL & PRIVACY  
     
  © 2014 - ZengaZ. Powered by Emo Creation